Ford F-150 (2009-2014) Double DIN or Single ISO with Pocket Radio Installation Dash Kit, Retains SWC & Factory Amplifier, Car Audio Wire Harness & Antenna Adapter Included

This fit perfect in my 2010 F-150. I recently purchased a 2010 F-150 with only 30K miles, it was a barn find. This kit worked great, fit really well, and was compatible with the new Pioneer Double DIN stereo I bought for it. It wasn't too difficult to install. If you have any mechanical ability, you should be able to do this yourself. Tip: The passenger side trim is held in place by a bolt that is behind the passenger airbag. You don't have to remove the trim completely, but you do need to move it a bit. I ended up cracking the trim because I didn't know about that bolt. You can remove the bolt if you open and remove the glove box. Take the bolt out so you don't make the same mistake I did. Also, use a safe-pry tool with care. I used a plastic trim tool and still scratched the silver trim panels, which I'm still yelling at myself about. The truck was like it just rolled off the dealership lot.

As described and looks good and fit good in my truck

Bought this for my work truck when I needed to upgrade the stereo. I had looked at others that were more expensive but it was going in my work truck so I got this one. I paid a local shop to install my stereo and they showed me one of the more expensive brands Metra to be exact, I couldn't tell the difference. Fits perfect the texture is a little different but not enough to bother me. 10/10 would recommend. The usb charging and android auto lines can be hooked into the old sync spot with some modifications. I had to dremel out some of the plastic then epoxy glued them into place but works and looks great. The only thing I would say is the wiring harness they sent wasn't compatible and I had to buy another one.

Overall, this dash kit fit my 2012 Ford F-150 fairly well. I did have a few issues, though. First, the instructions were basically non-existent. It took a lot of digging for me to figure out that the radio mounting tabs were apparently designed to fit several different vehicles and that you had to break off most of them to fit this truck. (Thanks, YouTube!). Second, the Emergency Flasher switch assembly (located above the new radio in the picture) didn't seem to fit as well in the new face plate as it did in the original. A bit of tweaking helped. The auxiliary port connector at the bottom (not shown) also did not fit very well and I'm still tweaking it. Lastly (and this may simply be an issue with the cheap radio I installed), the mounting tabs and the bezel around the radio don't exactly fit the radio very well. You may be able to see the gap at the bottom of the radio in the picture. It's not a show-stopper but again, this may be the fault of the radio I purchased. Overall fit and finish: Average to good Quality of instructions: poor Would I recommend this item? Yes, with the caveat that you need to be fairly handy to figure out how to make it work properly for your application. Overall, it looks fine for a decade old truck and I managed to get everything to function okay.

I usually don’t do many reviews. I thought I would on this product for a double din unit on my Son’s 2013. F150 worked very well. I was surprised how well the radio fit in the bracket thumbs up.

I have a company 2011 F-150 XLT truck which the factory radio went out years ago. The clock would just flash or sometimes the display would go out all together and had no music. I had an old radio laying around and this kit was cheap and had just about everything I needed One thing to keep in mind is that in the wiring harness , the 12v switch power wire is not present on the factory harness. You will need to connect that to a switch power source. I bought a fuse tap from autozone and connected to fuse 37 and it works when the ignition is on. Otherwise it don’t look bad , the texture of the kit matches the rest of the trim pretty good and I now have music again for long trips

First and foremost, this worked, in that it did what it was supposed to do. The price wasn't bad, and it had everything together, rather than having to piecemeal the harness, face, radio mounting hardware, and antenna adapter. The wiring harnesses and the radio mounting hardware were just fine. The faceplate, however, well, I should've spent a few bucks more and/or taken a bit more time to find a Metra or a Scosche kit, as I've *always* had good luck with those. As another has posted here in the comments, I had to trim the top hole (scraped the top and bottom to make it just a tiny bit "taller") for the hazard and traction control switches to fit properly, and even then, they didn't fit too well. The sides just didn't pinch and click in correctly; I had to wedge "stuff" on the sides of the switch to force the tabs out to make it stay. The bottom knock-out for the (no longer needed) Ford aux in didn't fit, either - it wasn't wide enough, and it was only after I broke the darn OEM part that I figured out the problem. There isn't enough surface to glue it, either, so I had to use a self-tap screw and two washers to hold it in (my OCD wouldn't allow for a gaping hole in the console). Fortunately, black electrical tape over the washers and bolt head "hide" it well enough from peripheral sight. Also know that, because Ford's engineers don't like us using aftermarket ANYTHING, you'll need to find power to connect to the RED wire in the Ford harness. I feel like Ford did it the dumbest way possible simply to make it easier for them. Maybe they figured that I'd go buy another $500 head unit from them rather than buying a $33 radio, $34 dash kit, and $7 fuse tap and installing it myself. Anyhow, I found power by running a 16-gauge stranded copper wire from the radio "hole to the passenger side footwell where Ford put the fuse box. You'll need to buy a fuse tap ($7 at Walmart, or Autozone - they have 'em on Amazon, too, but I didn't need a 10-pack.) You can easily run the wire by popping the glove box out (push in on both sides to drop it, but you don't need to take it off). NOW, Ford uses micro fuses, and the fuse tap is a "mini fuse," but that's OK - mini fuses will fit into micro fuse spaces, BUT you won't be able to put the inner fuse box cover back on after you're done unless you cut the cover, and it's just not worth it - the outer panel cover will still protect the fuse box. Tap onto fuse #38 - you'll need TWO 10 amp mini fuses - one for what you're doing, and 1 to replace what you removed when you pulled the micro fuse. (If you have a radio that needs more than 10 amps, then you'll need to find a fuse that matches the amperage of your head unit.) Fuse 38 is a START / RUN fuse. Run your fuse tap with the red wire running to the right (i.e. toward the seat) to properly install it. If you want to do research or meter the box out to find fuses that are powered in either RUN or ACC (accessory), go for it, but remember, your fuse tap has to FIT, and 38 did the trick nicely. If you don't use 38, you'll also need to meter the fuse spot to determine which side is hot - the side of the fuse tap opposite the wire should be the "hot" side. YouTube can tell you more. Obviously, you don't want to pick just any fuse in the box, as it may be "always on," and that'll drain your battery. Using #38, the radio WILL stay on when you shut the truck off for 10 minutes or until you open a door (whichever comes first).

Works perfectly in my 2010 f150 stx double din radio. Easy to install. You will need to find a viable 12v for the radio power. I to a splice from the air bag light and the radio works when I turn the key on and off

I swapped out a factory stereo for an F-150 and this was the perfect faceplate. I wasn't really able to find many options, but thankfully this one was there to pick! The faceplate fit well into the truck and the most difficult part of the installation was removing the metal clips from the original faceplate. My new double din head unit fit very well into this faceplate and there are no gaps (and I didn't need to use the extra spacer).

El articulo superó mis expectativas, biene con el arnes de cables para ford f150 (no se si para los demas modelos) lo mas importante es que: al venir con el arnes ya no hubo que cortar ningun cale del autoestereo, la carcasa encaja perfectamente, los laterales vienen con diversas lenguentas para ser atornillados, es decir, tiene multiples modos para su instalación. lo recomiendo al 100. llegó en tiempo sin ningun problema

La pieza frontal viene más pequeña y queda más corta en la parte de arriba , todo embona muy bien , y es de buen material, solo que viene más corta la parte de arriba y queda una ranura como de poco menos de un cm , no la regrese por qué ya había modificado las partes donde va colocado el stereo sino la hubiera regresado ya que no queda como la original, revisen esa parte antes de hacer cualquier modificación que les impida regresar el producto

Installed on my 2011 Ford F150. Had some wiring issues. Everything worked out well.

Faltaron cables