VS-20BLX

Great little safe..... I just love these safes.... and after looking around at numerous different brands, I always came back to Viking's safes as being the best value for the money... and also because of the quality of their build. Having 3 options to open them is a great feature. And because there is a key option, you won't ever get locked out of it, if the electronics ever fail. Being 64, I figured the fingerprint reader probably wouldn't work for me... but happily it did! I used my middle finger because my thumbs and index fingers always get cut, nicked, etc. working around the house. Sadly, it didn't work for my girlfriend, but it worked both for me, and my son. The keys are 4-sided, and very robust... not the kind of lock just anyone could pick, maybe only a locksmith could do it. Keypad works great... and a very nice feature is the LED light inside, which comes on when the door opens. They've generously supplied some hardware to anchor the safe to the floor or wall, but the idea didn't really appeal to me. You would either have to bolt it to the floor (which is not convenient) or to a wall stud which would not work very well. The small size would allow only 1 fastening point, since studs are 16" apart. My idea was to use some 3/16" steel aircraft cable, with a small loop on one end of the cable, feed the cable through the inside back hole, until the loop stops it. I made the cable 12' long. Then I drilled a 1/4" hole through my bedroom floor, behind the middle of my low dresser, through the carpet molding at the baseboard. That way, you can still take the molding off when you get new carpeting and locate the safe to anywhere on the dresser. I fed the cable into the basement, and secured the end of the cable (near the hole), in a circular fashion, using common cable/wire staples to the 2x10's holding the floor up, after bending the cable in a circle, and nailing the staples over the cable in all the curves. No thief is going to spend that much time trying to either cut the 3/16" cable, or pull out 8, 10, or 15 wire staples (your choice) on the basement ceiling. I happen to have a big, cable-crimping tool myself, and had to decide which sized wire would work for this securing problem. The next size down was 1/8" cable, and there was no doubt in my mind as to which cable was the right choice. The 3/16" cable looks massive next to the 1/8" cable (as shown in the pictures) even though it's only 50% larger. I have some good cable cutting nippers that cut the small stuff in a snap, whereas they couldn't cut the 3/16" stuff..... even my 18" long bolt cutters couldn't cut the bigger cable. I had to use a hammer and cold chisel, to actually cut the stuff.... Because of the stiffness of the wire, I found that the loop may turn (inside the safe) and cause the shelf to lift. It's not a big deal to just adjust the cable a bit to cure that, but I will make my girlfriend's safe just a bit different.... rather than making a loop, I made hers with a simple cable stop. These cannot be pulled off by any normal human, but for a bit more "extra" security I put 2 on, instead of one. These safes are well worth the money, and their representative Monica was very gracious... she answered all the questions I asked, and even had the boxes opened and quality checked, per my request, before shipment to me. Overall I am very satisfied with my purchase. I actually bought 3 of them... and everyone loves them. Hope you enjoyed my review.

I did a lot of research to try to get the best safe of this size at a reasonable price. Since it seems a lot of reviewers are compensated these days I will say definitively that I did NOT receive a discount or a free product for my review. I ordered it at the list price just like anyone else to store some "machined steel parts" that I'd prefer my kids didn't access without supervision. 1) This safe has a motorized actuator to retract the deadbolts rather than a knob that the user must twist. This obviously reduces the number of steps to open but more importantly limits vulnerability to "safe bumping" (look it up on YouTube) which many similar safes are vulnerable to. Since the person trying to bump can't load up the knob while bumping it that makes it impossible to bump, at least in the "traditional" manner. It's fast too. Should the mechanism fail the key can be used to retract the deadbolts manually. 2) The key mechanism seems very secure. It's a bit hard to get in (It only goes in one way even though it looks symmetrical) and you have to remove a plate to access the key hole but it's really just for access in a dead battery condition. It seems like it would be very difficult to defeat. 3) The reset button is well protected on the interior. Other similar safes have had vulnerabilities where a small hole could be popped in the plastic keypad then a wire could be used to fish around and press the interior reset button, restoring the default codes. This one would require drilling through metal to do this. It's not an impenetrable fortress obviously, but it's a very good strong box with quick auto-pilot access. The fingerprint reader is quite good. Not up there with TouchID on an iOS device but close. At first I only enrolled each finger once. This worked well but maybe 5-10% of the time I'd get "err" on a registered finger. I opted to go back and enroll a single finger on each hand 5x each. It's near 100% reliable now. On the screen sometimes it will recognize the same finger as one of the other ID#s that it was enrolled as rather than erroring out. Only one minor gripe about the beeper/documentation. It's not loud but it's a bit loud for certain applications. I wanted to turn it off so I consulted the documentation. It stated to press "0 & (*)" which I attempted, numerous times. To me (and I imagine most) the "&" indicates that both buttons should be pressed together so I didn't really even think about it. I spent 5 minutes or so doing different combinations. Press both briefly and simultaneously, press and hold 0, then press *, vise versa, etc. As it turns out you press 0 THEN * and it works fine.

I did a lot of research before buying my Viking VS-20BLX safe. The only negative I have found is the textured paint is so tough and thick it caused the door to be hard to open once the safe is unlocked. About 2 minutes work with some sand paper solved that problem. Take your time and read the directions for setting up the lock mechanism. They tell you everything you need to know in plain English. The safe locks and unlocks exactly as it should. You can turn off the key beeps so entering the combination or using the Biometric fingerprint reader is absolutely silent. There is a very slight gear noise as the mechanism retracts the locking bolts. Its very subtle and probably cannot be heard or identified across the average size bedroom. Overall the safe is well made, very sturdy and a great value with none of the security weaknesses of the competition. It's large enough to accommodate even large handguns. It can't be opened with a paper clip like one of the top brand safes. An 8 lb sledge hammer would beat the hell out of it but I doubt the safe can be opened that way either. Make sure you anchor it solidly. I didn't like the wall anchors that came with the safe. I could have used them but they were not the best for my installation. A few dollars at the local hardware store solved that problem. Some people have voiced problems with the biometic fingerprint reader. Even the paperwork that came with the safe recommended senior citizens not rely on the reader. Older folks have thinner dryer skin that's harder for the scanner to read. I HAVE DISCOVERED A SIMPLE WORK ROUND FOR THIS PROBLEM. BEING 66 I HAVE THE DRY THIN SKIN. I SIMPLY MOISTEN MY FINGER TIP SLIGHTLY ON MY TONGUE BEFORE PLACING IT ON THE READER. THIS WAY THE READER WORKS VIRTUALLY 100% OF THE TIME. I plan on buying a second VS-20BLX soon.

I love this product!! I’m very happy with my Viking Safe. It feels solid, well-made, and secure. Setup was easy, and the locking mechanism works smoothly. It’s the perfect size for storing important items without taking up much space. Definitely a good purchase and worth the money.

This is a great little gun safe, perfect for keeping my hand gun safely tucked away. Now I don't have to worry that my grandkids or any one else fir that matter will be able to get access to my gun when they are here visiting. The biometric scanner works every time. The scanner is the reason I chose this safe. My brother has one thats very similar and I was impressed at how easily the scanner worked. You can program in many sets of prints, 25 I think. So I've programed in mine and my husbands. The set up and programing was easy. I feel confident now that I'll be able to get at my gun quickly and easily if need be. The safe is small enough that I can take it with me in the car when I'm traveling.

I have had this safe for quite some time now. It is a great safe. Convenient to use. Compact size. Heavy enough to make it a chore to carry even at it’s size(a plus because it is not the kind of item that you want moving around) it is mountable and able to be secured in place. It is beautiful looking if you see beauty in metal. Functions as perfectly as can be expected. It is important to keep batteries fresh to avoid having to use the backup keys. It does use very little battery power and the batteries have lasted much longer than I expected. Because I have left the batteries in too long, I am having to contact customer service. They are also very good. Great response time. A great product from a great company. Good for personal use or professional use where multiple users can be added.

This safe is great, very easy to set up and secure. I’ve had it for years with no issue, just be sure to replace the battery as needed. It’s small, but holds a lot. Would purchase again.

I love this safe. It opens fast and easily and never fails me. Easy to secure to the wall as well.