Ferrite Core Noise Suppressor Beads - 20 Pack EMI RFI Filter Clips for USB Audio Video Cables, Multi-Size (3.5-13mm) Cable Management Solution for Electronics Interference Reduction

Pretty good products, they reduced both the low end hum (with the loop trick) and high end hiss (with the single wire through). I found placing the loop in the middle for lows was a good place, with the highs clip at each end close to the connection.

I was having a bit of RF or EMI interference issues while recording in my new space and thought I'd give these a shot as they are much cheaper than a power conditioner and yes they do seem to be reducing my RF/EMI interference issues and even seem to help a little with some background hiss on my audio a bit, but I'm very picky about my audio and I am listening to it through professional studio monitoring headphones, so people other than audio professionals and proper audiophiles may not notice any great difference, but they certainly seem to have worked for me. :)

I used these around the cable outputs of many switch mode power supplies and mains cables to reduce the amount of 'electrical noise' near to my hi-fi amplifier and other equipment. It was part of a 'housekeeping' project to tidy up the rats nest of cables behind the TV, separating switch mode supplies into a dedicated distribution block and physically distancing them from speaker cables etc. They are easy to use, just select the appropriate size and they just clip on. A cheap solution that will reduce electrical noise. My hi-fi amplifier was the only device that I didn't fit a ferrite bead to, as it has its own mains conditioning, that was just plugged into its own mains socket.

Does exactly what it says on the tin. Easy to use and sizes fit perfectly.

Good range of sizes in the package. However, used this on my computer's peripherals to reduce RF interference from my amateur radio, however it had no effect. There will likely be some devices or products that this will be useful for, but for amateur radio purposes, I recommend a toroid core instead (to wrap the wire or coax around multiple times).

I used a few of these on my HI-Fi system. At full volume I had a slight motor bike popping to go with my slight earth loop problem.I put one on the preamp mains lead ( fed by a Tacima strip), but no discernible difference. Same for power amp- at the equipment ends. Then put one on the phono input lead and hey presto the popping stopped. I put one on either end of my interconnect also for good measure. I’m still left with the slight earth loop hum (proved by temporarily substituting a transformer -it’s not staying as it greatly reduces sound quality) but of course that’s a different problem to the popping. As expected, no immediate noticeable difference to the sound of the music. Anyway the ferrite rings worked regards the popping and must be a good measure against other RF nasties. Good value and choice of sizes-press hard! ;-)

Did the job and has reduced the dabs dropping out not all the kit was required as some were too large but was as described

I had horrible noise coming through a new expensive phono pre-amp. tracked it down to the 40 year old cables from the vintage technics turntable. Clipped a couple of these on it- noise gone. Worth the money and I have a load left for any other problem issues

Die Ferritkerne sind ideal, um störende RFI- und EMI-Interferenzen in meinen Kabeln zu reduzieren. RFI (Radio Frequency Interference): RFI, oder Hochfrequenzstörung, bezieht sich auf die Störung, die durch unerwünschte Funksignale entsteht. Diese Signale können von vielen Quellen stammen, wie z.B. Mobiltelefonen, Funksendern oder elektrischen Geräten, und sie können den Betrieb von elektronischen Geräten beeinflussen, insbesondere solche, die auf Funkfrequenzen basieren, wie z.B. Radios oder drahtlose Kommunikationsgeräte. EMI (Electromagnetic Interference): EMI, oder elektromagnetische Störung, ist eine breitere Kategorie, die alle Arten von elektromagnetischen Störungen umfasst, einschließlich RFI. Diese Störungen können durch verschiedene elektromagnetische Quellen verursacht werden, wie elektrische Motoren, Transformatoren, Computer oder sogar Blitzschlag. EMI kann den Betrieb von elektronischen Geräten stören, indem es in die Signale eindringt, die diese Geräte senden oder empfangen. Ich verwende sie vor allem an meinen Audio- und Netzwerkkabeln, um unerwünschte Störungen und Brummen zu minimieren. Besonders gut finde ich, dass das Set eine Vielzahl von Größen bietet, sodass ich für jedes Kabel den passenden Ferritfilter finde. Die Installation ist kinderleicht, und die Ferritkerne lassen sich problemlos an den Kabeln befestigen. Die Störungsunterdrückung funktioniert hervorragend – klare Empfehlung für jeden, der saubere Signale benötigt!

Lo compré para reducir el ruido en un HUB USB y que provocaba que unos de los dispositivos conectados dejara de funcionar. Fue colocar uno en cada extremo y solucionado. Son de buena calidad, cierran bien. El único pero es el embalaje, es decir una bolsa de plástico muy frágil, eso sí, dentro del embalaje de Amazon

These things remove noise from audio cables. Easy to fit around the cable

Très bien pour l'utilisation qu'on lui demande. Attention si vous avez de fortes sections, ça n'ira pas (a vérifier dans les tailles).

Verkar vara lite klena. Och en del var svåra att stänga. Gjorde ingen större skillnad på störningarna jag ville dämpa.