Fast Setting Clear Epoxy

The product works well. No surprises. . The stopper or lid/cap that holds the liquid mixtures in is well designed and comes on and off easily. You don’t have to cut the tips and deal with annoying snap-on caps/lids. The lid/cap simply twists on and off. I’ve used the product four times already removing and putting back the lid/cap. No mess and the cap/lid works and comes on and off without issues. . The plunger is smooth and trouble free. . The two liquids come out clear and transparent, but turn slightly opaque when mixed. The epoxy mixes into a liquid consistency similar to chocolate syrup rather than tomato catsup, so viscosity is not that thick, so it will run. I recommend using a tray to mix. I used a piece of cardboard and experienced some running. . When applying, note that the epoxy is lesser in terms of viscosity. It will run off your scraper and spill, so take care. But spillage is easy to clean with a wet paper towel. . Don’t over-apply. Just make sure you can get even costing on both aurfaces/sides of the materials to be bonded. . No nasty odors. . A couple of minutes after application, the epoxy feels sticky and rubbery, but that goes away and the material will turn rock hard after an hour or so. Epoxy dries clear. Hardly noticeable even after applied on a wooden door that is painted white. . Very good bonding. I used masking tape to clamp/hold the glued pieces together. And the tape came off easily after curing/hardening. . I would most definitely buy this product again.

The. epoxy works great, other than the smell I would rate it a 10/10. It cures fast and holds like iron.

I used this for gluing a broken piece of ceramic together and also for kintsugi, mixing it with mica for color. It worked great as an epoxy, and for the kintsugi, filled a hole and dried hard as metal. So that function it great. I did however downgrade the “ easy to use” rating, because it didn’t dispense evenly. When I first pushed the plunger, it came out of one side before it did the other, as if there was an air bubble in one side. The amount evened out as I continued to push, and I dispensed more than I needed, to decrease the difference. It did dry hard, as a stated above, so maybe the 2 parts don’t have to be exactly the same amounts, but I did think it was worth mentioning. There was one feature that was very useful. The cap that you put Back on to store it only goes on one way, so you don’t have to remember how you took it off. There is no danger of left over harder in the cap mixing with left over resin in the plunger and glueing the whole thing shut.

Easy to use and fantastic durability. I've used it on many a project.

Used this epoxy as a finish top layer to cover a long (the >3 feet long) granite bench >1/4 inch-wide crack filled with strong adhesive glue and colored to match the granite. The gap of the long crack could not be clamped to be narrower without completely breaking the 2 -3 inch-wide long edge of the bench into many pieces. Plus there was a partially deteriorated supporting metal plank upon which the granite bench was glued, so the two pieces were hopelessly separated. Estimate prices to repair or replace the granite bench was ridiculously too expensive. So I used ChatGPT4.0 to come up with solution: First I cleaned out the gap with brush and vacuum. Then filled the length of crack with strong adhesive glue (LOCTITE PL Premium 10 oz. Polyurethane Construction Adhesive) from above and later from underneath where rust had deteriorated some of the metal support. I filled it just slightly below the surface level. I trimmed with a razor blade if it cured higher than surface level. Then I colored the visible tan colored glue with markers and acrylic paint to match granite colors and pattern. Finally, I applied this epoxy layer to protect the colors and pattern from water and make the repair flush with the surface of the rest of the bench. The epoxy was somewhat self-leveling, but can shave excess edges with razor as needed. Not bad for a DIY in an area not readily seen by visitors. Hope the epoxy can withstand the humidity and water exposure as the product claims it should.

My 3/8" Makita rechargeable drill had fallen off of the ladder and snapped the handle in half right above the battery. I removed the rubber covering on the area where the handle had snapped in half. The lower section of the handle that holds the battery had completely snapped off. The only thing holding the lower section together with the upper section was the wiring harness. It had left the lower section hanging with a half inch gap. I applied acetone to the broken area and areas around the break, to etch into the plastic. I applied the two-part epoxy to the brake, above and below the brake. I tightly secured the two halves together and let it sit overnight. I used the first coat of epoxy just as the base coat. I then took fiberglass mesh drywall tape and applied three layers of the mesh tape around the break in the handle. I applied the second coat of epoxy which was the first coat over the fiberglass drywall tape. I let.the second coat of epoxy dry overnight. Lastly I applied the third coat of epoxy,which was the second coat of epoxy over the fiberglass drywall mesh. I applied the second coat over the mesh strictly to thicken the coat that was covering the mesh. That was a week ago now. I have used the drill multiple times since the repair. The drill is working perfect, seems to be very strong and holding up well. The 3/8" drill casing itself is some type of hard plastic. I think that this epoxy works perfect for this application with the fiberglass mesh for added strength. I used this epoxy strictly for the strength and not for the aesthetics. I'm very happy with the end result. In my opinion it has completely repaired this 3/8" Makita rechargeable drill. Otherwise this drill would have been thrown into the trash.

Bought this in Jan 2021. Product was great to use but about after 7 months of ownership I noticed that the hardener was turning a yellowish color and eventually turned into the consistency of a hard paste that I could not get out of the tube easily. Had to separate the two plungers so that I could press the two sides with different pressure and continue to get some use out of the product. Since epoxy and hardener should last about 3 years, I am wondering how old these items are coming from the vendor's warehouse. This is the second time I buy this product. The last time I purchased two of these and was unable to use the second one because all the material (epoxy and hardener) had solidified in the tubes. Please note that these products were kept indoors at room temperature and well sealed with the cap provided.

This hid the cracks in an irreplaceable stained glass window.

Excelente epóxico, de verdad que sí pega el cristal, ya lo utilice en el cristal de mi comedor y de verdad que sí resiste..

Sent without packet - only the syringes were delivered wrapped in a plain plastic wrapper. No instructions for use were received.

اشتريت باقي التجربة ان شاء الله ممتاز

Muy buena aunque es muy poco precisa. Huele muy mal pero supongo que es por la resina.

This stuff is great! I bought it purposely to repair the lid of an old ceramic sugar bowl, of purely sentimental value. I already had superglue, which would probably have worked but does not give a very strong bond. I have used epoxy adhesives in the past for ceramic repair and often been disappointed by the poor fit of fragments and the yellowish lines of the adhesive that remains clearly visible between them. The simple dual-syringe mechanism works perfectly, as does the re-sealable cap. Working time is sufficient to mix the product, apply with due care to two surfaces and to press the pieces into position until they are fairly firmly fixed. It's worth noting that you also have a short time to wipe away any excess adhesive - definitely do this before it sets! I left the repair to cure fully overnight and the result is perfect - the join is almost entirely invisible.